|
 |
 |
 |
 |
 |
 |
 |
 |
 |
|
|
This is a general guide to stove / range fault code. This guide may be incomplete as manufactures use different parts on different models. We assume no responsibility for any action taken on your part as a result of using this guide. Consult your owners manual, as it may give the fault codes for your particular model.
| GENERAL ELECTRIC HOTPOINT RCA |
| Display | Condition | Repair |
| F0 and F1 | Failed Thermistor Control | Replace ERC |
| F2 |
Oven Temp Exceeds 590 w/unlocked door |
High resistance or interference in sensor Likely a bad sensor |
| F3 | Open sensor circuit |
Bad sensor or open sensor fuse |
| F8 | Component failure | Replace ERC |
| F9 | Program w/door circuit | Check Wiring |
| FRIGIDAIRE TAPPAN GIBSON WESTINGHOUSE |
| Display | Condition | Repair |
| F0 & F1 | EOC failure | Replace EOC |
| F2 | Oven too hot |
Likely a bad sensor (should read 1100 ohms) Possible bad EOC |
| F3 | Oven Sensor Open | Replace sensor |
| F4 | Oven Sensor Shorted | Replace sensor |
| F5 or F6 or F7 | EOC failure | Replace EOC |
| F8 | Lock switches | Check operation of lock switch(s) |
| WHIRLPOOL ROPER KITCHENAID |
| NOTE: Not valid for Y line. If there is a Y near the end of your model number, do not use this chart. |
| Display | Condition | Repair |
| 4 Digit Display | ||
| FO - E0 |
Analog to Digital Failure |
Disconnect for 30 seconds- if display re-appears- replace control |
| F1 - E1 | Safety flip flop | replace |
| F2 - E0 | shorted keypad | replace |
| F3 - E0 | sensor or sensor fuse opened | replace sensor or fuse |
| F3 - E1 | sensor shorted | replace sensor |
| F3 - E2 | oven too hot | replace sensor |
| F3 - E3 | clean temp. too hot | replace sensor |
|
F5 - E0 F5 - E1 and E2 |
check door/latch switch |
replace |
| 2 Digit Display | ||
| F0 or F1 or F5 | Failed transistor | Replace ERC |
| F2 | Oven temp too high |
1. Test operation of door lock on self-clean models. 2. Test relay contact operation 3. High resistance in sensor (should be apx. 1100 ohms) |
| F3 | Open sensor or thermal fuse | Replace sensor or thermal fuse |
| F4 | Shorted sensor | Replace sensor |
| F6 | Problem in time keeping circuit |
1. Reset time and/or cooking operation 2. Check for proper ground |
| F7 | Stuck function switch or button on ERC | Replace ERC |
| F8 | Failure of ERC | Replace ERC |
| F9 | Door lock circuit | Check wiring and test operation of door lock switch |
| MAYTAG MAGIC CHEF JENNAIR ADMIRAL |
| Display | Condition | Repair |
| F1 | watch dog on board |
bad touchpad or clock see FAQ for procedure |
| F2 | oven too hot |
bad relay board (if present) or bad sensor |
| F3 or F4 | open or shorted sensor | replace sensor |
| F5 |
hardware and watchdog circuits disagree |
replace clock |
| F6 | missing AC signal | Check for proper voltage |
| F7 | function key shorted | replace touch pad or clock |
| F8 | A/D supervisory | replace clock |
| F9 | door latch supervisory |
check door lock circuit or replace clock |
| F0 | function key stuck | replace touch pad or clock |
| AMANA CALORIC |
| Display -glass link ERC | Condition | Repair |
| door flashing #0,1,2,3 | latch switch broken | replace |
| lock flashing | latch switch broken | replace |
| F 0 | loss of safety signal | replace adapter board |
| F 1 | watchdog circuit | replace ERC |
| F 2 | oven too hot | check sensor-1100 ohms |
| F3 F4 | open or shorted sensor | replace sensor |
| F7 | shorted touch panel | replace glass panel |
| F9 | motorized door | check latch |
| FF | lock error | check switch and motor |
| ERC III / Relay board with separate board / push buttons | ||
| F0 | shorted push pad | replace |
| F1 | failed ERC | replace |
| F2 | oven too hot | check sensor 1100 ohms |
| F3 F4 | shorted or open sensor | replace |
| F5,F6,F8 | failed ERC | replace |
| F7 | shorted or sticking button | check glass alignment |
| F9 | door latch failure | replace |
|
|
|
|
|
|
|
|
|
|
|
AppliancePro is an affiliate of :
RepairClinic.com